26: You need to set up a password that will prevent unauthorized users from telnetting into your router. What series of commands would you use?
A. Acme1(config)# line console 0
Acme1(config-line)# password acme
Acme1(config-line)# login
B. Acme1(config)# line vty 0
Acme1(config-line)# enable password acme
C. Acme1(config)# line vty 0
Acme1(config-line)# enable secret acme
Acme1(config-line)# login
D. Acme1(config)# line vty 0
Acme1(config-line)# password acme
Acme1(config-line)# login
27: When you are setting up your serial interfaces, what does the clockrate command do for your connection?
A. Establishes the timing at which you send data
B. Establishes keepalives
C. Establishes the advertised bandwidth
D. Establishes the time on the router
28: You need to set up passwords on all your default Telnet lines. What command would you start with?
A. Router1(config)#telnet configuration
B. Router1(config)#interface Ethernet 0/1
C. Router1(config)#line vty 1 5
D. Router1(config)#line vty 0 4
29: You can execute show commands at which prompt? (Choose two.)
A. Router1#
B. Router1(config)#
C. Router1(config-router)#
D. Router1>
E. romon1>
30: You are configuring your router and type in an Enable password and an Enable Secret password. Your fellow network technician asks you why you have two passwords set when you need only one. What do you tell him?
A. The Enable password is used by low-level applications.
B. If you reverted to an older version of the IOS, it would not understand the Secret password.
C. Both passwords are treated the same.
D. It is a failsafe method of ensuring that people need to type two passwords instead of just one.
31: You need to get back to Privileged EXEC mode from Interface Configuration mode. What is the quickest method?
A. Ctrl+Shift+6; then press X
B. Ctrl+Esc
C. Ctrl+Z
D. Type exit
32: When you are establishing a PPP link, which of the following would be negotiated? (Choose three.)
A. IPCP
B. CHAP
C. UDP
D. Q.931
E. Multilink Protocol
33: Which of the following commands returns your router to a previously saved configuration?
A. Router1#setup
B. Router1#copy running-config startup-config
C. Router1#copy startup-config running-config
D. Router1#reload
34: You are in Interface Configuration mode and would like to recall the last command you typed, move your cursor to the beginning of the command line, and type no before the recalled command. You notice your up- and down-arrow keys do not function because you are using an older terminal program. What command combinations could you use to recall the previous command and move your cursor to the beginning of the line?
Press Ctrl+P to recall the previous command and Ctrl+A to move to the beginning of the command line.
Press Ctrl+L to recall the previous command and Ctrl+B to move to the beginning of the command line.
Press Ctrl+D to recall the previous command and Ctrl+A to move to the beginning of the command line.
Press Ctrl+E to recall the previous command and Ctrl+A to move to the beginning of the command line.
35: What is the baud rate setting for your terminal emulation program so that you can communicate through your console port?
A. 2400
B. 9600
C. 14400
D. 36300
36: What must be configured on a Cisco device to enable Telnet functionality?
A. A management IP address
B. SNMP
C. CDP
D. vty ports
37: You are configuring your Cisco router and need to go back to User EXEC mode. What command takes you back to User EXEC mode?
A. Router1#enable
B. Router1#exit
C. Router1#configure terminal
D. Router1#disable
38: Which of the following commands places an IP address on your Catalyst switch?
A. Switch1#ip address 10.2.2.2 255.255.255.0
B. Switch1(config)#Set IP 10.2.2.2 255.255.255.0
C. Switch1(config-vlan)#ip address 10.2.2.2
D. Switch1(config-vlan)#ip address 10.2.2.2 255.255.255.0
39: Which of the following commands would you enter to receive this output shown in the figure above?
A. Router1#show NVRAM
B. Router1#show Flash
C. Router1#show Flash-Mem
D. Router1#show Version
40: Your senior network administrator is unable to telnet to a Catalyst switch because she forgot the IP address. You have physical access and are able to console in. Which of the following commands is the best to get the IP address on the switch?
A. Switch1#show ip
B. Switch1#show vlan 1
C. Switch1#show ip route
D. Switch1#show interface vlan1 |
